Welcome to Yangzhou Guoxing Technology Co., Ltd [official website]
The daily maintenance and advantages of Guoxing Technology Plasma Cleaning Machine, Yangzhou Guoxing Technology Co., Ltd. was registered and established in Yangzhou Jiangdu in 2019 under the guidance of the government's industrial policy. Yangzhou Guoxing is a high-tech company integrating R&D, production and sales. It is committed to providing customers with plasma etching and surface cleaning equipment, as well as supporting sales of electronic additives. Guoxing Technology will explain to you the daily maintenance and maintenance of high-temperature and high-pressure cleaners mainly as follows: A. Please use clean tap water directly from the tap to the machine to supply water, and it is strictly forbidden to contain sand and other impurities in the water; B. Rinse the water pipes and the inside of the equipment to prevent rust and impurities before use; C. Please use 10# or higher quality diesel as fuel. There must be oil in the fuel tank at all times. Moisture and impurities are strictly prohibited; D. Execute the switch program, turn off the hot water when it is off, and continue to rinse until the equipment is completely cooled, then turn off the cold water; E. It is forbidden to place the equipment in an environment where the temperature is lower than 0 degrees Celsius to prevent the remaining water from freezing; F. The equipment power supply is 380V, 50HZ, and the yellow/green wire is required to be grounded; G. Water pump lubrication: the amount of lubricating oil in the water pump shall not be less than the oil level of the red dot in the center of the oil window; H. The oil must be changed after the pump works for 50 hours for the first time, and the oil shall be changed every 1000 hours after work I. The diesel filter must be replaced or cleaned in time; J. Clean the fuel tank: unscrew the oil drain nut at the bottom of the engine, drain the remaining diesel, and then rinse the fuel tank with clean diesel, and then tighten the oil drain nut; K. Due to working in a high-pressure environment, nozzle wear is inevitable, so it must be replaced in time. Properly lowering the pressure can prolong the service life of the nozzle and high-pressure water pipe; L. Frequently flush the scale deposited in the water inlet pipe. Troubleshooting: 1. The water gun does not spray water, the pressure is insufficient, and the water gun trembles. Reasons and countermeasures: insufficient water supply, blocked water inlet filter, blocked gun nozzle, and sand in the water causing the pressure regulating valve Severe wear and long-term use will cause scale blockage of the heating coil, damage to the water inlet filter, impurity entering the blocking check valve, freezing and cracking of the pump body and water leakage; the ceramic plunger is freezing and cracking; the detergent tank is empty and the switch is turned on; the pump The body seal is damaged; the bypass valve is blocked, which makes the automatic stop heating system function invalid, and burns the heating coil. 2. The heating system does not ignite or works badly. Reasons and countermeasures: check the fuel tank oil level; check whether the diesel filter is blocked; Check whether the flexible connection between the diesel pump and the motor is broken; check whether the diesel pump is damaged; check whether the solenoid valve is open; check whether the temperature control switch is damaged; check whether the fuel injector is blocked; check whether the high-voltage cable package is damaged; check whether the spark plug gap is too large The spark is too weak; the fuel quality is unqualified and the combustion deposits block the air loop; check whether the pressure switch is damaged; check whether the air inlet volume matches; check whether the heating coil is damaged; check whether the temperature detector is damaged; the gun tip is severely worn The outlet pressure is low. 3. It is very important to choose a set of refrigerant recycling and refilling equipment that suits you. A, understanding your applicable refrigerant type B, reliable product quality and perfect after-sales service is very important C, clear the classification of recycling and filling equipment And application scope D, some issues that should be paid attention to in the purchase: (1) Whether the compressor, vacuum pump, etc. are imported products. These components determine the quality of the equipment to a large extent. (2) If the equipment comes with weighing For your system, it is necessary to confirm whether the weighing system can complete the correct shutdown (for example, the pressure of the refrigerant storage tank is too high) and start your function (for example, automatic filling operation). This determines the degree of automation of a device. Guoxing Technology will explain to you what are the advantages of using a plasma cleaning machine? 1. Plasma cleaning machine can not use harmful solvents, so no harmful substances will be produced after cleaning. This effectively solves the problem of environmental protection. Plasma equipment can be classified as a green cleaning. 2. The product after being cleaned by the plasma equipment is already very dry, so the next process can be carried out without drying. 3. Plasma cleaner is a plasma generated with high frequency in the radio wave range. It is different from the direct light such as lasers that we usually come into contact with. Because its directionality is not strong enough, it can penetrate into the fineness of the object. The holes and recesses complete the cleaning task, so there is no need to worry about the shape and angle of the objects being cleaned. Of course, it is easier to achieve better results with vacuum plasma equipment. 4. The cleaning process of the plasma cleaning machine can be completed within a few minutes. It has the characteristics of high efficiency and high speed cleaning. 5. Plasma equipment can perform plasma surface treatment for different substrates, different shapes, regardless of the object to be processed, whether it is semiconductor, oxide, or polymer materials. It can also use selective materials for overall or complex structures, and can also achieve cleaning treatments such as partial structures. Our products are mainly used in the manufacturing fields of semiconductors (chips and packages), panels and camera modules, electronic circuit boards, automobiles, medical and cosmetics, etc. Our customers include Luxshare Precision, Oufeiguang, Huahong Grace, Samsung Electronics, Taiwan Xinxing Group and other electronic manufacturing companies. Daily maintenance and advantages of Guoxing technology plasma cleaning machine。
Consult now